Alcatel-Lucent OmniAccess Access Points work with OmniAccess WLAN switches/controllers to provide a high performance wireless mobility solution for enterprises. They can be securely deployed in a variety of locations such as on walls, cubicles, desktops, and in the ceiling, and the AP antenna diversity allows for the best possible signal processing using dual, omni-directional antennas.
One of best use cases for using OmniAccess Wire Access Point is where we have dense no. of users as client associated capacity is very good. Also one of the use case is when administrator wants different PSK for each user for authentication. OmniAccess WAP supports in better way.
In a corporate environment that requires strong security and the ability to block / allow a large variety of users, the Cisco Wireless platform excels. The system is extremely robust and can provide literally a blanket of coverage, with very good performance. They also offer external/out doors access points which provide excellent performance. Because the system is well built and designed, you often go through the lifetime of the product (you really need to apply updates) with very little issues. However, when you reach the end of the support life on the box, it is not cheap at all to upgrade/replace. You really need to keep an eye on the current life cycle and plan accordingly for a replacement date and fund.
It's Cisco and like all our other Cisco products, chiefly switches, once you get it set up to your liking, it just runs itself after that. The reliability factor has been huge for us.
Ease in deploying new APs has been nice. We have a DNS record (and DHCP Option 43 as a fallback) that helps new AP find the WLC. The WLC takes it from there.
Good monitoring of connections, kicking people off, [and] blocking certain MACs are all useful features.
Configuring wireless settings is very confusing because various settings are scattered all over the interface in different tabs
Lots of settings use Cisco's technical verbiage rather than common phrasing, so it's confusing what a lot of settings will do and requires researching the meaning before modifying the setting
The interface could be easier to use to do simple tasks such as reboot an access point
Although it is a very good product, support is easy and can manage by Level 1 support persons and downtime is too much less but still there is a cost factor matters which is consider by each organization. Furthermore, organizations also compare with other competitors so it is hard to pursue and defend the high prices.
As I said before, the only thing we miss in our old model is the fact that the management interface never received an improvement in design. It has the same look and feels since it was launched. It's not that it's hard to use. It's just the case of could be modernized.
Downtime fear is the first fear which IT persons look and want to eliminate as much as they can but eventually you have to face it as nothing is perfect. Cisco Wireless Lan controller are feasible to use and easy to manage and other than this their issue reported are pretty low so you can get the best up time. now it also depends on scenario as well as environment.
Cisco Wireless Lan controller are feasible to use and easy to manage and other than this their issue reported are pretty low so you get the better uptime. if your get the uptime then it means its a stable product in your environment. Product performance also depends on the product management and Cisco Wireless Lan controller management is easy so you can get the great output.
As usual, the support from Cisco's TAC (Technical Assistance Center) is lacking. Granted, they always get the job done, but the amount of lead time on a non-emergency is enough to make you just handle it yourself. The good news is that if you ask for Cisco's assistance and forget about it, they'll jump on by the time you've forgotten where you were in troubleshooting it and have it fixed for you.
Originally, when we deployed our first controller it was on a very limited basis. We only deployed it to our administration building and our High School. It was pretty straight forward. Because this was new to us we leaned heavily on our Cisco partner to assist us. With our last upgrade, we upgraded the controllers, added redundancy and expanded the building count along with new SSID's and restrictions. It went much easier, but again, we did rely on Cisco TAC and our partner to clarify and assist as needed. Having already been familiar with the product help tremendously.
Have used Cisco Meraki access point earlier having management on cloud and is on license (subscription basis). But Alcatel OmniAccess Points have management on cloud, on premise as well which means to say flexibility in terms of management. We had one requirement where we number of user is large which is going to connect on access point but Cisco Meraki only supports 200 users per radio whereas OmniAccess point have better client associated capacity with 524 per radio.
The Aironet access points are used for employee WiFi access, and they integrate well with Meraki. They would offer a separate guest network, too, but the decision was made to physically separate the guest network, so even if a bad actor would gain access to the ethernet port of the AP, they'd still not see any company traffic.
Cisco is a brand name and people trust on it. if any one thing about the networking then Cisco is among those brand which is count as trusted brand and people rely on it. Also it support is good so people can use it. Cisco Wireless Lan controller are easy to use and manage so it requires less effort.
Positive impact 1. Our employees are able to move around anywhere in our 12-story building and have access to our corporate network. Employees are not tied down to an office and can easily move around to meetings and stay connected.
Because the equipment is so reliable, we do not have any unscheduled outages. Employees come in the building and connect without issues and have a sense that the wireless network "Just Simply Works."
When performing network maintenance, I usually have to block out several ours for our maintenance window. Upgrades sometimes do not go as smoothly as planned. This can be frustrating for the engineer.
